Category: Analogue Output Signal Conditioners

Products ► Instrumentation ► Analogue Output Signal Conditioners

Analogue Output Signal Conditioners

Please find all models below ▼

_________________________________
Categories
Analogue Output Signal Conditioners

Model LVDT OBSOLETE

LVDT Signal Conditioner and Amplifier Model LVDT OBSOLETE

Bulkhead

LVDT Signal Conditioner and Amplifier

  • LVDT sensor excitation of 4.5 V RMS is provided
  • Selectable sensitivity from 20 mV to 10 V and fine trim with potentiometer
  • Analogue outputs of 4-20 mA & 0-10 V
  • Selectable excitation frequency between 1 and 5 kHz
Categories
Analogue Output Signal Conditioners

Model SGA A&D

Strain Gauge Signal Conditioning for Load Cells Model SGA A&D

Bulkhead

Strain Gauge Signal Conditioning for Load Cells

  • Strain gauge amplifier ideal for load cell signal conditioning
  • Bridge excitation of 10 V DC with drive for four 350 Ohm load cells
  • Conditioned output signal can be selected from 0-20 mA, 4-20 mA, 0-10 V, 0-5 V, ±5 V or ±10 V
  • 1 – 5 kHz adjusted filter for test & measurement applications
Categories
Analogue Output Signal Conditioners

Model SGABCM

Bridge Completion Module for the SGA Model SGABCM

Bulkhead

Bridge Completion Module for the SGA

  • Easy installation – simply screws into the existing load cell connector on the SGA
  • On-board screw terminal connections accept a wide range of bridge completion resistor enabling on-site installation without soldering equipment
  • High stability resistors (5ppm/°C) fitted for the ‘fixed’ arms of the bridge
Categories
Analogue Output Signal Conditioners

Model ILA

In-line Strain Gauge or Load Cell Analogue Amplifier Model ILA

In-Line

In-line Strain Gauge or Load Cell Analogue Amplifier

  • Quick setup & semi-automatic calibration via USB programmer module and free Toolkit software
  • High accuracy measurement
  • Low temperature drift provides stable, reliable measurement
  • Extensive EMC filtering reduces noise for safe operation
  • Small robust design, ideal for compact installations – 80 x 24 x 15 mm
Categories
Analogue Output Signal Conditioners

Model ILE

In-Line Housing for Load Cell Amplifiers and Digital Converters Model ILE

In-Line

In-Line Housing for Load Cell Amplifiers and Digital Converters

  • In-line housing for load cell amplifiers ICA and digital load cell converters DCell
  • The ILE and ICA converts a load cell to a conditioned load cell
  • The ILE and DCell converts load cell to a digital load cell
  • Very small size – 56 x 28 mm excluding glands
  • Machined from solid stainless steel
  • Waterproof to IP67 NEMA
Categories
Analogue Output Signal Conditioners

Model ALA5

ATEX Certified 4-20 mA Load Cell Amplifier Model ALA5

ATEX Approved

ATEX Certified 4-20 mA Load Cell Amplifier

  • ATEX certificated amplifier for hazardous zones 0, 1 & 2
  • Designed for fitting in-line to strain gauge sensors such as load cells
  • Intrinsically safe to EN60079-11
  • Provides 2-wire 4-20 mA current loop output
  • Environmentally sealed to IP67
Categories
Analogue Output Signal Conditioners Controllers & Alarms

Model LCD20

Load Cell DIN Rail Signal Amplifier Model LCD20
Load Cell DIN Rail Signal Amplifier Model LCD20

DIN Rail

Load Cell Signal Amplifier

  • Intelligent, compact, stackable microprocessor based load cell amplifier for smarter automation and process control
  • Fully isolated standard analogue outputs 4-20mA and 0-10V
  • Full digital setup & easy programming via USB connection to a PC using intuitive toolkit software
Categories
Analogue Output Signal Conditioners

Model JBA

Active Summing Load Cell Junction Box Model JBA
Active Summing Load Cell Junction Box Model JBA

DIN Rail

Active Summing Load Cell Junction Box

  • Accurate and easy summation of up to 4 strain gauge load cells
  • Corner correction enabled to compensate for manufacturing tolerances and loading in multiple strain gauge installations
  • Individual gain adjustment provided for each channel
  • Simplifies installation of multi-cell platforms, silos, tanks and hopper weighing systems
Categories
Analogue Output Signal Conditioners

Model ICA5ATEX

ATEX Certificated Miniature Load Cell Amplifier Model ICA5ATEX

Embedded

ATEX Certificated Miniature Load Cell Amplifier

  • ATEX certificated amplifier for hazardous zones 0, 1 & 2
  • Miniature PCB format for fitting inside sensors, 19 mm diameter, 7.6 mm height
  • 2 wire current loop 4-20 mA output
  • Low interaction between the trimmers makes calibration fast and easy
Categories
Analogue Output Signal Conditioners

Model ICA H & S

Miniature Strain Gauge Amplifier, Converts Load Cell to 4-20mA & 0-10V Model ICA H & S

Embedded

Miniature Strain Gauge Amplifier

  • Fits inside sensors, 19.5 mm diameter, 7.6 mm height
  • Outputs of 4-20 mA, 0-10 V, 0-5 V, ±10 V
  • Non interaction between the trimmers makes calibration fast and easy
  • High speed 1000 Hz
  • 2 wire 4-20 mA load cell option